DuraPuds 703

DuraPuds 703

Through coloured thin coat finishing mortar

For fine rendering of soft-moulded bricks

  • Suitable as top surface on mineral substrates.
  • For interior and exterior use
  • Water and weather-resistant
  • Fully covering uniform colours
  • Diffusion open
  • High yield
  • Coat thickness 1 - 3 mm

Product calculator

Product facts

Product

Cement-based powder containing polymer modifiers.
Added light-stable pigments. Contains quartz sand with grain sizes up to 0.8 mm.

Colours

Available in through-coloured white and natural cement grey.

Coverage

Coverage

1.5 – 2.0 kg/m² per mm coat thickness.

Packaging

Available in 20 kg PE lined paper bags.

Features

Generel

Expected Result

Application

Waterproofing

Surface preparation

Fixing dowels

Finishing

Sealings

Flooring

Precautions

Alfix A/S H.C. Ørsteds Vej 11-13 DK-6000 Kolding alfix.com
10
Ydeevnedeklaration nr. 10 EN 998-1:2010 Alfix DuraPuds 703
Mineralsk puds
CS IV
Brandklasse A1 Varmeledningsevne λ10,dry ≤ 0,83 W/(m⋅K) for P=50% λ10,dry ≤ 0,93 W/(m⋅K) for P=90% (tabelværdier efter EN 1745)
Vandabsorption W0
Diffusionsmodstands-faktor µ ≤ 25
Vedhæftning på beton ≥ 0,08 N/mm² Holdbarhed / frostresistens NPD

Tile fixing

Tile fixing

Tests

Surfaces

Technical data

Working temperature

+5°C - +25°C

Density

1.55 kg/ litre (mixed with water)

Working time

3-4 hours at +20°C

Water vapour diffusion

µ-value: ≤25

Drying time

24 hours at min. +15°C

Fully cured/ready to receive further treatment

7 days at min. +15°C

Shelf life

Min. 12 months in unopened bag

How to use

Surfaces

Soft-moulded bricks, dried and cured
Extruded/wirecut bricks.
Aerated concrete
Cement/sand rendering, older than 48 hours
Concrete, older than 14 days, max. 90% residual moisture
Light-weight concrete, max. moisture content 8%
Existing tiles. For interior use only.
Painted surfaces. For interior use only.
Paper-faced plaster boards, fibre-reinforced plaster boards
Cementious or polystyrene wet-room tilebacker-boards, such as Aquapanel, Powerpanel H2O,
Hydropanel, Ivarit UniCo, and Internit VR. For interior use only.


For further information, please consult our Technical Services Dept.

Surface preparation

Brickwork, soft-moulded bricks: The surface should be dimensionally stable. Brickwork should appear
sound with compacted, filled joints. Prior to rendering, ensure that brickwork is completely cured and dry
with no blooms or efflorescence. For high- suction substrates, wet the brickwork prior to application.
Older, existing brickwork, soft-moulded bricks. The surface should be dimensionally stable, clean from
dust, mortar residues, grease, salt, fouling and other contaminations. Low pressure sand blasting may be
required. Use the smallest amount of water possible and leave the brickwork to dry.
In case of exterior use, a thin contact layer of Alfix DuraPuds 710 is recommended if the surface has a
low or limited absorbance capacity.
Brickwork made of machine-made bricks: Brickwork should appear sound with compacted, filled joints.
Prior to rendering, ensure that brickwork is completely cured and dry with no blooms or efflorescence.
Older, existing brickwork should be dimensionally stable, clean from dust, mortar residues, grease, fouling
and other contaminants.
Machine-made bricks or bricks with a low absorbance capacity should always be provided with a contact
layer of Alfix DuraPuds 710.
Aerated concrete, cement/sand rendering, concrete, light-weight concrete: For very absorbent interior
surfaces, such as aerated concrete, prime with Alfix PlaneMixPrimer diluted 1:3.
For exterior use, apply a thin contact layer of e.g. Alfix LetFix.
Boards, existing tiles and painted surfaces: A thin contact layer of for example Alfix LetFix or Alfix
DuraPuds 710 should be applied on the surface. Must dry until next day.

How to use

Add approx. 4.4 – 4.8 litres of clean, cold water per 20 kg powder. Pour water into a clean container, sprinkle in powder while stirring until a smooth paste is obtained. Leave the mixture to rest for a few minutes, and the mortar is ready for use.

Apply Alfix Durapuds 703 with steel float and spread in a thin layer. Leave to dry until the render no longer “sticks” when touched. Continue by rubbing and smoothing the surface with a sponge. To avoid visible lines of colour differences, it is recommended to finish each wall in one ongoing work process.


NB!
Additional water should not be added to a mixture already starting to set.
When using coloured finishing render, consistent water dosage and even final smoothing are crucial factors in order to obtain a good result.
Exterior rendering should only take place in dry weather at temperatures from +5°C - +25°C. Avoid direct sunlight. If rainy weather or temperatures below +5°C are forecast, cover surfaces. Avoid exterior rendering during winter.

Cleaning

Clean residues from tools with water before the mortar sets. Cement-based products harden when mixed with water, hence do not dispose of excess material by pouring into drainage system.

September 2017

Read the latest Alfix newsletter: New "LEGO House" in Billund...

 

Read moreSee the archive here

 

Highly professional, technical services

Seek technical service and advice for professional building projects

How to use your Alfix product

How to ensure your DIY project a good start