ProFix

ProFix

Flexible tile adhesive - Light

  • For ceramic and quarry tiles, mosaics and natural stone
  • For large-sized tiles and porcellanato tiles
  • For interior and exterior use
  • Coverage as 25 kg traditional tile adhesive
  • Eeasy-flowing consistency for floors
  • Rapid strength development
  • Approved for wet rooms
  • Suitable for underfloor heating
  • Bed thicknesses up to 10 mm

Product calculator

Product facts

Product

Light grey, cement-based powder containing light fillers and high-performance polymer modifiers.

Colours

Coverage

Coverage

Notched trowel
Coverage per m²
4 x 4 mm
approx. 1,0
6 x 6 mm
approx. 1,5
8 x 8 mm
approx. 1,9
10 x 10 mm
approx. 2,4
12 x 12 mm
approx. 2,9
For straightening/ levelling
1,0 kg/mm

 

For fixing tiles and natural stones in bed thicknesses exceeding 10 mm, it is possible to add kiln dried sand - grain size 0-2 mm. Please observe specified mixing instructions before adding any sand to the mixture.

 

Recommended bed thickness
Mix proportion per 20 kg Profix
Max 15 mm
5 kg
Max 20 mm
8 kg

Packaging

Available in 20 kg PE lined paper bags.

Features

Generel

Expected Result

Application

Waterproofing

Surface preparation

Fixing dowels

Finishing

Sealings

Flooring

Precautions

Alfix A/S H.C. Oersteds Vej 11-13 DK-6000 Kolding alfix.com
09
Declaration of performance
No. 6
EN 12004:2007+A1:2012
Alfix ProFix Improved cementitious
adhesive for internal
and external tiling
Reaction to fire NPD Release of dangerous
substances
See material safety data
sheet www.alfix.com
Bond strength: Initial
tensile adhesion
strength
≥ 1,0 N/mm² Durability, tensile adhesion
strength after heat
ageing
≥ 1,0 N/mm²
Durability, tensile adhesion
strength after water
immersion
≥ 1,0 N/mm² Durability, tensile
adhesion strength after
freeze/thaw cycles
≥ 1,0 N/mm²

Tile fixing

Tile fixing

Tests

DS/EN 12004 - DS/EN 12002

Surfaces

Technical data

Working temperature

+5°C - +30°C

Density

1.4 kg/litre (mixed with water)

Open time

20 – 30 minutes

Working time

4 hours at +20°C

Foot traffic/grouting

12 - 18 hours at +20°C
24 – 48 hours at +10°C

Tensile adhesion strength

concrete :1.0 – 2.0 N/mm²

Classification - DS/EN 12004

C2 E S1

Shelf life

Min. 12 months in unopened bag

How to use

Surfaces

Cement/sand rendering, brickwork, aerated concrete
Screed, with or without underfloor heating, older than 14 days
Light-weight concrete, max. moisture content 8%
Flooring containing cement-based levelling compound.
Anhydrite floors, max. residual moisture 0.5%
Concrete in situ and precast units/slabs, older than 2 months
Paper-faced plaster boards, fibre-reinforced plaster boards
Existing tiles, terrazzo
Vinyl and paint on concrete
Alfix Sealing Membrane

Plaster, wood, existing tiles, vinyl, and paint are not considered suitable surfaces for exterior use or in areas exposed to frequent or permanent water

Surface preparation

The surface should be dimensionally stable, sound, and clean. Free from laitance, grease, and dust. There should be no blooms or crack formations. Residues from grease or soap can be removed with Alfix Deep Cleaner. Ensure that paint is sufficiently adhering and non-flaking. Sand/Matt vinyl and paint with the appropriate sandpaper and apply a thin contact layer of Alfix ProFix.
Straightening of lumps and unevenness of up to 10 mm can be carried out using Alfix ProFix.
On absorbent, moisture sensitive interior surfaces, such as aerated concrete, gypsum plaster, plaster boards, and anhydrite floors, apply Alfix Primer (Sealing Primer) or Alfix PlaneMixPrimer.
For exterior use, apply a thin contact layer of Alfix ProFix.

How to use

Add approx. 0.27 – 0.35 litres of clean, cold water per kg powder corresponding to 5.4 – 7.0 litres of ready mixture per 20 kg bag depending on whether to use as non-slip wall adhesive or pourable floor adhesive.

Apply Alfix ProFix to the surface with a notched trowel, using the straight edge to spread out adhesive and subsequently the notched edge to produce a ribbed bed.

Fix tiles within 20-30 minutes by pressing them firmly into position in the wet adhesive with a slight twisting action. When fixing mosaics, a firm tap is required.
Ensure complete adhesive coverage!

For tile sizes exceeding 60 X 60, apply adhesive to both tiles and surface to ensure solid bedding leaving no voids (buttering/floating method).

For exterior use, e.g. stairs and facades, regardless of tile size, always apply buttering/floating method.

 

NB!

Large-sized tiles and natural stone may call for extra attention.
Additional water should not be added to adhesive already starting to set. Note that the temperature of mixing water will influence setting time.

Repositioning of tiles should be done within approx. 20 minutes after fixing, depending on substrate and tile absorbency.

Switch off any underfloor heating.

Cleaning


Clean adhesive residues from tools and tiles with water before the adhesive sets. Cement-based products harden when mixed with water, hence do not pour surplus adhesive into the drain system.

September 2017

Read the latest Alfix newsletter: New "LEGO House" in Billund...

 

Read moreSee the archive here

 

Highly professional, technical services

Seek technical service and advice for professional building projects

How to use your Alfix product

How to ensure your DIY project a good start