Flexible tile adhesive
- For interior and exterior use
- For ceramic tiles, quarry tiles, mosaics, natural stone and porcellanato tiles
- For fixing insulating plates
- Execellent adhesion to existing tiles and vinyl
- High tensile and shear strength
- Approved for wet rooms
- Suitable for underfloor heating
- Bed thicknesses up to 5 mm
Grey, cement-based powder containing high-performance polymer modifiers.
Available in 5 kg and 20 kg PE lined paper bags.
|Alfix A/S H.C. Oersteds Vej 11-13 DK-6000 Kolding alfix.com
|Declaration of performance
Alfix CombiFix Improved cementitious
adhesive for internal
and external tiling
|Reaction to fire||NPD||Release of dangerous
|See material safety data
|Bond strength: Initial
|≥ 1,0 N/mm²||Durability, tensile adhesion
strength after heat
|≥ 1,0 N/mm²|
|Durability, tensile adhesion
strength after water
|≥ 1,0 N/mm²||Durability, tensile
adhesion strength after
|≥ 1,0 N/mm²|
+5°C - +30°C
1.6 kg/litre (mixed with water)
approx. 30 minutes
approx. 5 hours at +20°C
24 – 48 hours +20°C
14 days at +20°C
1.2 – 2.2 N/mm²
0.7 – 1.2 N/mm²
Min. 12 months in unopened bag
Cement/sand rendering, brickwork, aerated concrete
Screed, with or without underfloor heating, older than 14 days
Light-weight concrete, max. moisture content 8%
Flooring containing cement-based levelling compound.
Anhydrite floors, max. residual moisture 0.5%
Concrete in situ and precast units/slabs, older than 6 months
Paper-faced plaster boards, fibre-reinforced plaster boards
Existing tiles, terrazzo
Vinyl and paint on concrete
Plaster, wood, existing tiles, vinyl, and paint are not considered suitable surfaces for exterior use or in areas exposed to frequent or permanent water.
The surface should be dimensionally stable, sound, and clean. Free from laitance, grease, and dust. There should be no blooms or crack formations. Residues from grease or soap can be removed with Alfix Deep Cleaner.
Ensure that paint is sufficiently adhering and non-flaking. Sand/Matt vinyl and paint with the appropriate sandpaper and apply a thin contact layer of Alfix CombiFix.
Straightening of lumps and unevenness of up to 5 mm can be carried out using Alfix CombiFix.
On absorbent, moisture sensitive interior surfaces, such as aerated concrete, gypsum plaster, plaster boards, and anhydrite floors, apply Alfix Primer (Sealing Primer) or Alfix PlaneMixPrimer.
For exterior use, apply a thin contact layer of Alfix CombiFix.
How to use
Add approx. 0.25 litres of clean, cold water per kg powder.
Apply Alfix CombiFix to the surface with a notched trowel, using the straight edge to spread out adhesive and subsequently the notched edge to produce a ribbed bed.
Fix tiles within 20-30 minutes by pressing them firmly into position in the wet adhesive with a slight twisting action. When fixing mosaics, a firm tap is required.
Ensure complete adhesive coverage!
For exterior use, e.g. stairs and facades, regardless of tile size, always apply adhesive to both tile and surface to ensure solid bedding leaving no voids (buttering/floating method).
Natural stone may call for extra attention.
Additional water should not be added to adhesive already starting to set.
Note that the temperature of mixing water will influence setting time.
Repositioning of tiles should be done within approx. 20 minutes after fixing, depending on substrate and tile absorbency.
Switch off any underfloor heating.
Clean adhesive residues from tools and tiles with water before the adhesive sets. Cement-based products harden when mixed with water, hence do not pour surplus adhesive into the drain system.