Frontpage Products Tile adhesives "Fix" LetFix - DISCONTINUED - replaced by LetFix Plus

LetFix - DISCONTINUED - replaced by LetFix Plus

Flexible tile adhesive - Light

For ceramic and quarry tiles, mosaics and non-moisture-sensitive natural stone
Suitable for tile formats up to 600 x 600 mm
For interior and exterior use on floor and wall
For coverage as 25 kg traditional tile adhesive
Fixing of insulating plates
Smooth and light-weight with non-slip properties
Suitable for underfloor heating
Bed thicknesses up to 5 mm

Calculate

Retailers

Product information

Application

Surfaces

Cement/sand rendering, brickwork, aerated concrete
Screed, with or without underfloor heating, older than 14 days
Light-weight concrete, max. moisture content 8%
Flooring containing cement-based levelling compound.
Anhydrite floors, max. residual moisture 0.5%
Concrete in situ and precast units/slabs, older than 6 months
Paper-faced plaster boards, fibre-reinforced plaster boards
Existing tiles, terrazzo
Vinyl and paint on concrete
Plaster, wood, existing tiles, vinyl, and paint are not considered suitable surfaces for exterior use or in areas exposed to frequent or permanent water

Surface preparation

The surface should be dimensionally stable, sound, and clean. Free from laitance, grease, and dust.
There should be no blooms or crack formations. Residues from grease or soap can be removed with Alfix
Deep Cleaner. Ensure that paint is sufficiently adhering and non-flaking. Sand/Matt vinyl and paint with
the appropriate sandpaper and apply a thin contact layer of Alfix LetFix, mixed with Alfix FlexBinder, if
appropriate.
Straightening of lumps and unevenness of up to 5 mm can be carried out using Alfix LetFix.
On absorbent, moisture sensitive interior surfaces, such as aerated concrete, gypsum plaster, plaster
boards, and anhydrite floors, apply Alfix Primer (Sealing Primer) or Alfix PlaneMixPrimer
For exterior use, apply a thin contact layer of Alfix PlaneMixPrimer mixed with water at a ratio of 1:6.

How to use

Add approx. 0.4 – 0.5 litres of clean, cold water per kg powder depending on whether to use as non-slip wall adhesive or pourable floor adhesive.
For optimal standing strength, add a maximum of 0.43 liters of water per kg powder.
Mix to a lump-free mass, maximum mixing time 1 minute.
Apply Alfix LetFix to the surface with a notched trowel, using the straight edge to spread out adhesive and
subsequently the notched edge to produce a ribbed bed.
Press/wiggle the tiles in place in the moist adhesive immediately – and within no more than 20–30 minutes. When installing mosaics, smooth the ridged layer of adhesive from the notched trowel to create a level bed of adhesive. Press/tap the mosaic tiles in place in the moist adhesive using a grout float, for example. Ensure complete adhesive coverage!
For tile sizes exceeding 600 x 600 mm, apply adhesive to both tiles and surface to ensure solid bedding
leaving no voids (buttering/floating method).
For exterior use, e.g. terraces, stairs and facades, regardless of tile size, always apply buttering/floating
method.
Tile formats larger than 600 x 600 mm will require extra drying time and will take longer to be ready for foot
traffic/grouting. Alternatively, you can use: Alfix ProFix, Alfix CombiQuickFix and Alfix QuickFix premium.

NB!

Additional water should not be added to adhesive already starting to set. Note that the temperature of mixing water will influence setting time.

Repositioning of tiles should be done within approx. 20 minutes after fixing, depending on substrate and tile absorbency.
Switch off any underfloor heating.

Cleaning

Clean adhesive residues from tools and tiles with water before the adhesive sets. Cement-based products harden when mixed with water, hence do not pour surplus adhesive into the drain system.

Downloads

	Alfix A/S H.C. Oersteds Vej 11-13 DK-6000 Kolding alfix.com 05	Declaration of performance No. 5	EN 12004:2007+A1:2012 Alfix LetFix Improved cementitious adhesive for internal and external tiling
Reaction to fire	NPD	Farlige stoffer	See material safety data sheet www.alfix.com
Bond strength: Initial tensile adhesion strength	≥ 1,0 N/mm²	Vedhæftningsstyrke efter varmelagring	≥ 1,0 N/mm²
Durability, tensile adhesion strength after water immersion	≥ 1,0 N/mm²	Vedhæftningsstyrke efter frost-tø lagring	≥ 1,0 N/mm²

LetFix - DISCONTINUED - replaced by LetFix Plus

Product

Coverage

Packaging

Precautions

Tests

Technical data

Surfaces

Surface preparation

How to use

Cleaning

Guidance

Downloads

Product Info

EMICODE

EPD

Material Safety Data Sheet