QuickFix premium

QuickFix premium

Rapid-setting natural stone adhesive

  • For sensitive natural stone, such as marble
  • For large-sized and porcellanato tiles
  • For interior use in dry and wet locations
  • Prevents discolouration and efflorescence
  • Easy-flowing consistency for floors
  • Foot traffic and grouting after 3 hours
  • Suitable for underfloor heating
  • Very low emission EC1 plus
  • Bed thicknesses up to 10 mm

Product calculator

Product facts


White, cement-based powder containing light fillers and high-performance polymer modifiers.




1.0 – 2.9 kg per m2


Available in 4 kg and 20 kg PE lined paper bags.



Expected Result



Surface preparation

Fixing dowels





Alfix A/S H.C. Oersteds Vej 11-13 DK-6000 Kolding alfix.com
Declaration of performance
No. 15
Alfix QuickFix premium
Improved cementitious
adhesive for internal

Reaction to fire NPD Release of dangerous
See material safety data
sheet www.alfix.com
Bond strength: Initial
tensile adhesion
≥ 1,0 N/mm² Durability, tensile adhesion
strength after heat
≥ 1,0 N/mm²
Durability, tensile adhesion
strength after water
≥ 1,0 N/mm² Durability, tensile
adhesion strength after
freeze/thaw cycles
≥ 1,0 N/mm²

Tile fixing

Tile fixing


DS/EN 12004 - DS/EN 12002


Technical data

Working temperature

+5°C - +30°C


1.2 kg/litre (mixed with water)

Open time

15-20 minutes

Working time

Approx. 1 hour at +20°C

Foot traffic/grouting

3 hours at +20°C
12 hours at +10°C

Full strength

24 hours at +10°C

Tensile adhesion strength

concrete :1.0 – 2.0 N/mm²

Classification - DS/EN 12004

C2 FE S1

Shelf life

Min. 12 months in unopened bag

How to use


Cement/sand rendering, brickwork, aerated concrete.
Screed, with or without underfloor heating, older than 14 days and max. humidity of 90% RH in moisture-resistant natural stone.
Light-weight concrete, max. moisture content 8%
Flooring containing cement-based levelling compound.
Anhydrite floors, max. residual moisture 0.5%
Concrete in situ and precast units/slabs, older than 2 months
Paper-faced plaster boards, fibre-reinforced plaster boards
Existing tiles, terrazzo.

Surface preparation

The surface should be dimensionally stable, sound, and clean. Free from laitance, grease, and dust.
There should be no blooms or crack formations.
Straightening of lumps and unevenness of up to 10 mm can be made using Alfix QuickFix premium.
On absorbent, moisture sensitive interior surfaces, such as aerated concrete, gypsum plaster, plaster boards, and anhydrite floors, apply Alfix VådrumsPrimer (Sealing Primer) or Alfix PlaneMixPrimer.

How to use

Add approx. 0.24 – 0.27 litres of clean, cold water per kg powder depending on whether to use as non-slip wall adhesive or pourable floor adhesive.
Use the entire mixture within 1 hour. Please notice that each new mixing procedure requires the use of clean container and mixing tools.
Apply Alfix QuickFix premium to the surface with a notched trowel, using the straight edge to spread out adhesive and subsequently the notched edge to produce a ribbed bed.
Fix tiles within approx. 20 minutes by pressing them firmly into position in the wet adhesive with a slight twisting action. When fixing mosaics, a firm tap is required.
Ensure complete adhesive coverage!
For natural stone, especially translucent types, and for tile sizes exceeding 60 x 60 cm, apply adhesive to both tiles and surface to ensure solid bedding leaving no voids (buttering/floating method).



Additional water should not be added to adhesive already starting to set. Note that the temperature of mixing water will influence setting time.
Repositioning of tiles should be done within approx. 10 minutes after fixing, depending on substrate and tile absorbency.
Alfix QuickFix premium is designed to prevent or reduce the risk of staining but under certain conditions, staining may unfortunately still occur. Hence, for receptive and moisture sensitive stones it is recommendable to trial a small area to ensure that tile and adhesive are compatible. For further advice, please contact our Technical Services Dept.
Alfix QuickFix premium is not suitble for use in areas permanently exposed to water, such as pools.
When adding Alfix FlexBinder to the mixture, a flexible adhesive for use on critical, demanding substrates is obtained. Only for fixing of ceramic tiles.
For grouting of natural stone, it is recommended to use Alfix QuickFuge 8 premium.
Switch off any underfloor heating.



Clean adhesive residues from tools and tiles with water before the adhesive sets. Cement-based products harden when mixed with water, hence do not pour surplus adhesive into the drain system.

August 2019

Alfix CeraFill 10 colour Universal grout has been improved, and its name is now being changed to UniversalFuge - CeraFill 10.


Read moreSee the archive here


Hochprofessioneller technischer Service

Kontaktieren Sie uns für Beratung und Unterstützung in Ihrem professionellen Bauprojekt.

So verwenden Sie Ihr Alfix-Produkt

Wie Sie mit Ihrem DIY-Projekt einen reibungslosen Start hinlegen