Rapid setting flexible tile adhesive
- For ceramic and quarry tiles, natural stone, large-sized tiles and porcellanato tiles
- For levelling, straightening of uneven screeds and slope building
- For interior and exterior use
- Suitable for low temperatures
- Grouting after 3 hours
- Long open time
- Smooth consistency
- Ideal for underfloor heating
- Very low emission
- Bed thickness: 2 - 10 mm
Light grey, rapid setting, cement-based power containing high-performance polymer modifiers.
Available in 20 kg PE lined paper bags.
|Alfix A/S H.C. Ørsteds Vej 11-13 DK-6000 Kolding alfix.com
|Ydeevnedeklaration nr. 4||EN 12004:2007+A1:2012
Alfix CombiQuickFix Hurtighærdende, cementbaseret fliseklæber med forbedret vedhæftning, deformation og åbentid. Inden- og udendørs anvendelse.
|Brandklasse||NPD||Farlige stoffer||Se sikkerhedsdatablad på www.alfix.com|
|Vedhæftningsstyrke efter tørlagring||≥ 0,5 N/mm²||Vedhæftningsstyrke efter tørlagring||≥ 1,0 N/mm²|
|Vedhæftningsstyrke efter varmelagring||≥ 1,0 N/mm²||Vedhæftningsstyrke efter vandlagring||≥ 1,0 N/mm²|
|Vedhæftningsstyrke efter frost-tø lagring||≥ 1,0 N/mm²|
DS/EN 12004 – DS/EN 12002
+5°C - +30°C
1.4 kg/litre (mixed with water)
approx. 30 minutes
approx. 50 minutes at +20°C
3 hours at +20°C
12 hours at +10°C
3 days at +20°C
1.0- 2.0 N/mm²
C2 FE S1
Min. 6 months in unopened bag
Cement/sand rendering, brickwork, aerated concrete
Screed, older than 14 days.
Light-weight concrete, max. moisture content 8%
Flooring containing cement-based levelling compound.
Anhydrite floors, max. residual moisture 0.5%
Concrete in situ and precast units/slabs, older than 2 months.
Paper-faced plaster boards, fibre-reinforced plaster boards
Existing tiles, terrazzo
Vinyl and paint on concrete
Plaster, existing tiles, vinyl, and paint are not considered suitable surfaces for exterior use or in areas exposed to frequent or permanent water.
The surface should be dimensionally stable, sound, and clean. Free from laitance, grease, and dust. There should be no blooms or crack formations. Residues from grease or soap can be removed with Alfix Deep Cleaner.
Ensure that paint is sufficiently adhering and non-flaking. Sand/Matt vinyl and paint with the appropriate sandpaper and apply a thin contact layer of Alfix CombiQuickFix.
Straightening of lumps and unevenness of up to 10 mm can be carried out using Alfix CombiQuickFix.
On absorbent, moisture sensitive interior surfaces, such as aerated concrete, gypsum plaster, plaster boards, and anhydrite floors, apply Alfix Primer (Sealing Primer) or Alfix PlaneMixPrimer
For exterior use, apply a thin contact layer of Alfix CombiQuickFix.
How to use
Add approx. 0.22-0.25 litres of clean, cold water per kg powder corresponding to 4.4-5.0 litres of ready mixture per 20 kg bag.
Apply Alfix CombiQuickFix to the surface with a notched trowel, using the straight edge to spread out adhesive and subsequently the notched edge to produce a ribbed bed.
Fix tiles within 15 minutes by pressing them firmly into position in the wet adhesive with a slight twisting action. When fixing mosaics, a firm tap is required.
Ensure complete adhesive coverage!
For tile sizes exceeding 60 X 60, apply adhesive to both tiles and surface to ensure solid bedding leaving no voids (buttering/floating method).
For exterior use, e.g. stairs and facades, regardless of tile size, always apply buttering/floating method.
Large-sized tiles and natural stone may call for extra attention.
Additional water should not be added to adhesive already starting to set. Note that the temperature of mixing water will influence setting time.
Repositioning of tiles should be done within 20-30 minutes after fixing, depending on substrate and tile absorbency.
Switch off any underfloor heating.
Clean adhesive residues from tools and tiles with water before the adhesive sets. Cement-based products harden when mixed with water, hence do not pour surplus adhesive into the drain system.